Skillet Steak Bites Recipe with Garlic Butter 15 min | Best Recipe B (2024)

FAQs

Should you butter steak before searing? ›

Because of this, if you heat up a pan hot enough to sear your steak, putting a dollop of butter in first means it is likely to burn up. However, that doesn't mean you can't still get the delicious flavors of butter with your steak. Rather than using it as your cooking oil, considering using it as a finishing oil.

Adding butter to steak is completely based on your personal preference but here are a few reasons that professional chefs approve of doing so: It increases flavor and richness. It makes for a glossy finish. It enhances the steak's texture.

If marinated, pat steak tips dry with paper towels to remove excess marinade. Preheat a large cast-iron skillet (or another oven-safe skillet) on the stove over medium-high heat. Add your preferred high-temperature cooking fat. Sear the steak tips for one minute per side.

Many different cuts, seasonings and cooking methods can result in a delicious piece of meat. But if you're aiming for a seared crust, a tender and juicy inside, and rich flavor in each bite, cooking steak with butter on the stove top might be your best bet.

Most vegetable oils have a higher smoke point and are better for high-temperature cooking. Canola and grapeseed also have less assertive flavors and are good to use for things like searing meat, making mayonnaise, and even popping popcorn.

There are many spices available for seasoning a steak, with salt and pepper topping the list. However, other spices, like thyme, rosemary, garlic powder, and minced onion, are also good options to enhance your steak's flavor. Or, use a one-and-done approach with Chicago Steak Seasoning.

Meanwhile, heat a cast-iron skillet over medium-high heat. Add steaks and cook until medium or medium-rare, 5 to 7 minutes. The last 2 minutes of cooking, add lemon halves, cut-side down, to pan to caramelize. Remove lemons and steak to a cutting board.

To reduce the amount of smoke, start with oil, rather than butter. We recommend around 1/2 cup for a 12-inch skillet. A few minutes before you finish cooking your steak, add butter and aromatics.

Place your cast iron skillet on the stovetop, set to medium-high heat, and add the butter. Once the butter has fully melted, add the steaks and cook them for 4-5 minutes per side or until they reach your desired level of doneness. Step 3- Let the steaks rest, then slice and serve.

When to add garlic when cooking steak? ›

Season: Sprinkle each side of the steak generously with salt and pepper, then immediately place in the skillet. Sear Side 1: Cook for 2 – 2.5 minutes until you get a great crust, then turn. Garlic Butter: Leave for 1 minute, then push steaks to one side and toss in butter, garlic and thyme.

Add 2 tbsp unsalted butter to the top of each steak during the last few minutes of cooking, spooning butter over steak as it melts. Remove the steaks from the skillet and let rest for 3 to 5 minutes.

Sear first in oil and then add butter.

Starting the steak in a few tablespoons of vegetable oil gives it a nice initial crust. Waiting to add the butter until the steak has been seared for about 4 minutes helps prevent it from burning.

Pat steaks dry with paper towels. Season liberally with salt. Allow to rest at room temperature for at least 40 minutes and up to 2 hours. Alternatively, place on a plate or on a rack over a baking sheet in the refrigerator overnight.

The Easiest, Cleanest Way to Sear Steak

Don't add oil. Start in a cold pan (no need to preheat). Flip the steaks every 2 minutes. Start with high heat, and then after a few flips, turn it down to medium.

High Heat Searing

Season your steak with salt, pepper, and any additional spices you love. Once the cooking surface is scorching hot, carefully place the steak on it, allowing a gorgeous sear to develop. You won't need any added fats; the high heat will create its natural non-stick surface.

Sear first in oil and then add butter.

Starting the steak in a few tablespoons of vegetable oil gives it a nice initial crust. Waiting to add the butter until the steak has been seared for about 4 minutes helps prevent it from burning.